Supplies Needed

• Pledge
• Brasso brass cleaner
• A soft cloth or two to clean with, preferably microfiber or an old tshirt
• Rubber glove (optional)
• Old toothbrush (optional)

Instructions

1. I start with the brass on my harness because the cleaner can get on the leather. Put on your glove and either put some Brasso on the cloth, or on your glove, and rub it in a circular motion on each brass part of your harness. The more tarnished the brass is, the more you’ll need to rub to clean it up.
2. Once you’ve restored the shine, use a clean portion of your rag to wipe off the rest of the product.
3. Repeat for the rest of the brass on your harness. TIP: Unbuckle each piece to work on it, then redo the buckle before you continue so you don’t change the way your harness is fitted for your horse! You can use the opposite side of the harness to remind yourself where to redo the buckle.
4. If your cloth is covered in Brasso, use a different cloth for cleaning with Pledge. Spray the pledge on your cloth (NOT on the harness) and rub it on the leather portions of the harness, taking care to avoid the embroidery.
5. For hard to reach areas of the harness, spray Pledge on the toothbrush and gently use it to clean those areas, then wipe them dry with the cloth.
6. Repeat until you’ve finished cleaning your harness!
7. Head to an AMHA show and get it dirty again!

Find your next miniature horse driving prospect with Little America. We have foals by LR Phantom’s Secret Storm, son of 35-time World Champion Single Pleasure Driving and Roadster horse, Silver Meadow’s Phantom Storm.

We also own 22-time AMHA World Single Pleasure Driving and Roadster winner, Lymrick’s Irresistible Force, “Guinness” and have his progeny for sale. Not only has Guinness won World Reserve Grand Champion Single Pleasure Driving Horse in both open and amateur, but he’s also been World Grand Champion Roadster Horse at AMHA World!

The post How to Clean a Miniature Horse Driving Harness appeared first on Little America Miniature Horses.

“Lifetime Achievement

The Lifetime Achievement Award is given to a nominee who has been an AMHA member in good standing for a minimum of five years. This individual is to have demonstrated an exceptional and specific contribution toward the perpetuation, use and/or breeding of the American Miniature Horse. They have earned documented recognition and respect as a positive, active and inspirational representative of the American Miniature Horse Breed and of the Association, having clearly served to strengthen the foundation and to direct the vision of the breed and/or the association.

Shared from Pete and Jennifer Welma’s nomination letter: Many of you know Mr. Tony Greaves, either through his constant smile and friendly demeanor or for the fact that he has been involved in the miniature horse industry for over fifty years. Tony has served the American Miniature Horse as a showman, educator, breeder and most of all an advocate for the breed himself.

Tony Greaves came from a long line of horsemen. He grew up on his family’s Quarter horse ranch but was inspired to own a Miniature horse by a Bozo the Clown comic book he read as a child. Fifty years ago, in the spring of 1963, Tony’s first miniature-sized horse, “Big Un,” was born. And in 1978 when the AMHA was founded, Big Un was Tony’s first AMHA registered horse, measuring at 31 inches tall. From there Tony began breeding Miniature horses in earnest, naming his farm Little America Miniature Horses. Today that farm in Buda, Texas is home to approximately 200 Miniatures. Tony is an international breeder, selling horses in Scotland, Thailand, Mexico, Russia and France. Each horse sold proudly carries the Little America name prefix. And they number almost 900 now.

Tony’s commitment to his business of breeding and selling Miniatures is just a small part of his passion. His enthusiasm and knowledge propelled him toward a more active role in 1993 when he became AMHA’s Secretary. From there his involvement blossomed as he served as Vice President (twice) and President of AMHA (3 times). He continued to be very involved and served on the Board of Directors and in 2005 received a well deserved “A” Award for Volunteerism.

Also in 2005, Tony’s daughter Lauren started a program called Thursday Kids that allowed children of all ages to come to the ranch and learn about Miniature horses. Now, seven years later the program is still going strong thanks to Tony and Lauren’s tireless efforts to educate children about the amazing Miniature horse, all the while promoting AMHA by supporting its shows and involving families that would not have otherwise ever been introduced to a Miniature horse. Tony uses every opportunity to share the Miniature horse with his community. The list of ways he’s found to showcase them is staggering from festivals and parades to career days at schools, Pet Appreciation Days, local nursing homes and yearly barn tours in his community.

But the most personal way Tony has found to share his love of the Miniature horse is with the hands-on approach that he uses with the numerous children that visit the farm every week. Kameron Welma is one of those fortunate kids who won the friendship of this amazing man over the past four years. Kameron soon learned the rules of the barn, “brush, water, check and clean the stalls and no running in the barn area.” In appreciation of the responsibility, knowledge and skills Tony bestowed, Kameron is now more confident, has a better attitude and his self-esteem has grown leaps and bounds. During the four years, Kameron has been involved in the Thursday Kids, he has won countless ribbons, belt buckles and other outstanding rewards. But he counts Tony’s friendship as his biggest win so far.

It seems fitting to award Tony Greaves this lifetime achievement award for his continued drive and faithful service to promote the Miniature horse and the AMHA on this 50th anniverary of the registration of his first Miniature horse.

Congratulations Tony!”

The post 2013 “A” Awards appeared first on Little America Miniature Horses.

“Jumps for Hunters and Jumpers will be made of 1-1 1/2″ schedule 40 PVC piping or other suitable light-weight material with jump cups, not to include pegs, nails, bolts, etc.  All jumps must be a minimum of five (5) feet wide… Jumps thirty-two inches (32) or more in height must have a second rail added.  All post and rail jumps must have a ground pole.  Uprights are to be a maximum of forty-eight (48) inches in height. …Any decorations or jump wings must not protrude more than twenty-four (24) inches from the uprights.”

Supplies

• ??— 10′ length of Schedule 40, 1.5″ diameter PVC pipe (Use the underlined totals in the directions to calculate how many 10′ lengths you will need according to how many jumps you want to make, and which height of uprights you want–hunter and/or jumper.)

  

• 2-4 — 1.5″ PVC caps (2 for hunter uprights, 2 for jumper uprights)
• 2– 1.5″ PVC T connectors
• 2-6– 2″ PVC T connectors (For jump cups. 2 for hunter uprights, 4 for jumper uprights because jumps over 32″ in height must have a second pole added to keep horses from running under.. trust me, I had it happen at a show once when the rule wasn’t followed!  I like to have a cup/D-ring on both sets of uprights so I don’t have to change them out when I switch from hunter to jumper)
• 4– 1.5″ PVC Elbow connectors
• 2-6– D-rings (To hold jump cups. 2 for hunter uprights, 4 for jumper uprights. I like to have a cup/D-ring on both sets of uprights so I don’t have to change them out when I switch from hunter to jumper)
• 12– 1″ Sheet metal screws
• Saw
• Drill and bits
• Screwdriver

Directions

1. Cut the 1.5″ diameter PVC into the following lengths:

• Long side of base and jump pole length: 5′ (x3 for hunter, x4 for jumper) = (15′ of PVC used for only hunter, 20′ if doing jumper for an extra jump pole)
• Short side of base length: 10″ (x4) = 40″= (3.33′ of PVC used)
• Jumper uprights: 4′ (x2) = (8′ of PVC used)
• Hunter uprights: 3′ (x2) = (6′ of PVC used)

2.  Now it’s time to assemble the base!  Attach one 10″ piece to each of the two opposite ends of the T (x2) to form the sides of the base.
3.  Attach the elbows to the open ends of the 10″ pieces that are attached to the T (x4), with the open end of the T facing straight up so the uprights can go in later.
4.  Use two of the 5′ lengths to attach the two ends of the base and complete the rectangular base.
5.  Place the uprights in the T on the jump.  Put a cap on the top of each jumper or hunter upright pole.
7.  Use your measuring tape to mark where you will drill holes on the uprights:

• Hunter: By AMHA rules, hunter jumps have a minimum jump pole height of 18 inches and maximum of 28 inches, so I recommend starting with a hole at 18 inches, and ending at 28.
• Jumper: By AMHA rules, jumper jumps have a maximum jump pole height of 44  inches, so you don’t need holes past 44 inches from the ground.

8.  Time to drill holes for the uprights!  Grab a bit that’s bigger than the peg of the D-ring you’ll be using.  It’s hard to get the holes aligned perfectly through the upright and through the cup later, so you’ll want some wiggle room.  Get them as straight through both sides of the pvc as you can.
9.  Now onto the jump cups.  Take your oversized Ts and cut out a little more than half of the  section that branches out (see below).  You want it to be a little over half gone so it makes it easier for the jump pole to fall down.  That way your jump doesn’t get broken when a horse hits it!  Then drill a hole through both sides for the D-ring to go through.

10.  To keep the base together, I recommend that you use sheet metal screws.  You DON’T want to use PVC glue, because if any piece gets broken, you’ll have to cut it off and splice it together.  With the screws, everything stays together but if something gets broken, you can take it off without cutting.  We use screws at every connection point on the base except where the uprights go in.

11.  The final step is to put the jump cups on the up uprights, pins in, and adjust the length of your jump poles.  For measuring everything out, it’s easiest to use 5′ for jump poles, but for them to fall out of the jump easily, they need a few more inches taken off.  Just put the poles in the cups and see how much you want taken off, it should be at least two inches.

12.  Congratulations!  You’re now finished and can enjoy your jumps!  To learn how to make striped jump poles, visit our other blog post, How to: Paint Obstacle/Jump Poles.

The post How to: Build jumps appeared first on Little America Miniature Horses.

For their April/May issue, AMHA ran an article in the Miniature Horse World about how Thursday Kids began.

Here are some of our favorite pictures from other shows in 2012.

The post 2012 Show Season appeared first on Little America Miniature Horses.

project and decided I’d use it to enhance our obstacle/jump course.  Since then, I was given three more cans of paint (one that’s fluorescent yellow!), so I’m now working on some more jump poles and figured I’d share the main way I go about painting them, as well as a few other options for having decorated obstacle poles.

Supplies

• • • PVC pipe of the diameter and length you want
    • Spray paint suitable for plastic surfaces (one or more colors)
    • 1″ masking tape
    • Several feet of string (length of the pole or could use a measuring tape instead)
    • A pencil
    • Two plastic bags (I use bread bags)
    • A sandwich bag or regular plastic bag (to protect your hand while spraying)
    • Two clothespins
    • A couple of paper towels or an old sponge
    • Scissors

Directions

1. Read the directions on your spray paint can to make sure it’s an appropriate day for painting!

   

2. Wet a paper towel or  and clean any dirt off of the PVC pipe that is to be painted.

   

3. ***For if you want to have a base color instead of white.  If not, move on to question number four*** shake up the paint and then put the sandwich bag on your hand to keep the paint off and spray away!  I hold one end of the pole up while I spray.

   

4. Get a piece of string and cut it to be the same length as the pole.  Decide on a width/spacing for your stripes, then use the string to measure even spaces/stripes by folding in half and marking it with a permanent marker or tying knots in the string at appropriate spots.  You could also use a measuring tape instead and skip this step, I just find the string to be foolproof, I have a tendency to mess up numbers!

   

5. Use a pencil to mark the appropriate spots along your rope or measuring tape.

   

6. Run masking tape around the pipe along the outer-most side of each stripe’s pencil marks (My pictures end here because I realized that previous poles that I had painted with this paint were fading because the paint was NOT for plastic!  Make sure you use paint that is for plastic.)
7. Make a hole smaller than the pole’s diameter in each of the bread bags and pull them onto the pole, stopping at the middle of the masking tape.  You don’t want any paint to leak past the tape, so use a clothespin to secure each bag and keep it out of your way.
8. Follow the directions on your spray paint can to get it ready.
9. Prop the pole up or just hold one end up with a hand.
10. Put the sandwich bag on the hand you’ll be spraying with!!  You could also use a rubber glove or bigger plastic bag.  Trust me, if you don’t use something, you’ll end up looking like you have chickenpox or something weird going on with your hand for several days.  I learned this the hard way after doing my first poles in red!
11. Apply second coat after around 10 minutes (or whatever your directions say), if you want.
12. Allow it to dry, then move the bags to the next stripe to be painted!

    

–Lauren Greaves

The post How to: Paint Obstacle/Jump Poles appeared first on Little America Miniature Horses.

FORT WORTH — Kameron Welma led a miniature horse around the ring, feeling the dirt floor with his small feet clad in cowboy boots.

Kameron peered out from under a large black cowboy hat and squinted at the judges. Born four months premature, the 9-year-old is legally blind.

Kameron, of Kyle, a suburb of Austin, won two third places Sunday at the Stock Show miniature horse show.

“I can’t see out of this eye,” Kameron said, pointing to his right eye while carrying his ribbons. “I can see really big stuff, just not the small stuff.”

Kameron was among the children from Thursday Kids, started by Lauren Greaves in the Austin suburb of Buda to introduce children to Little America Miniature Horses. Every Thursday after school, kids spend a couple of hours feeding, cleaning, brushing and learning about the horses.

Greaves, who began Thursday Kids as a high school student, asked her father, Tony, to continue the program when she left for college. She returned this year after graduating from Texas A&M and runs Thursday Kids with her parents.

“It gives the kids a sense of accomplishment and leadership and a creative outlet,” Lauren Greaves said. “And it teaches them about this wonderful breed.”

A miniature horse is no bigger than a large dog, according to the American Miniature Horse Association.

Drawn to the horses’ kind, gentle nature, the Greaves family owns about 170 miniature horses and provides them free to Thursday Kids families. Children as young as 3 have participated in the program.

More than three years ago, Sarah Johnson, 14, of Lockhart visited the Greaves’ home on a 4-H trip and then begged her mother to let her return. As an animal lover, she now looks forward to Thursdays all week.

“I just love the horses and love spending time with them,” Johnson said. “They’re smaller so you don’t feel scared at all.”

For Kameron, who cannot play team sports because of his eyesight, working with the horses has built self-confidence, said his father, Pete Welma.

“Having a commitment one day a week to clean stalls, brush and clean the horses and practice showing has taught him a lot about responsibility,” Pete Welma said. “It has been incredible for all the kids.”

  

Original article posting

The post Fort Worth Stock Show hosts members of Thursday Kids miniature horse program appeared first on Little America Miniature Horses.

The post SAAMHC Family Fiesta Show appeared first on Little America Miniature Horses.

Paula, Tyler, Kameron, Anijah had a fun time with their families at the Youth Calcutta party. Kameron won High Point Boy 7 & Under for the show as well as Special Needs Showmanship World Champion.

The post World Show 2010 appeared first on Little America Miniature Horses.